Every thermodynamics chapter ends up with the same four words: isothermal, isobaric, isochoric, adiabatic. Students learn each in isolation, then see a P-V graph with four curves and cannot say which is which. The cure is to follow one gas through all four, with the same starting point, and to ask the same three questions each time: what stays fixed, how much work is done, and where does the energy go.

One gas, four routes: the area under each curve is the work done

The first law is the only tool you need

Q = ΔU + W

Heat added to a gas either raises its internal energy or is used as work done by the gas. For an ideal gas, ΔU = nC_vΔT depends on temperature change alone, and W = ∫P dV is the area under the curve on a P-V diagram. Two more facts: C_p − C_v = R, and for a monatomic gas C_v = 3R/2 and C_p = 5R/2.

The setup

Take 1 mole of a monatomic ideal gas at 300 K and 1.0×10⁵ Pa. Its volume is V = nRT/P = 8.314 × 300 / 10⁵ ≈ 0.0249 m³, about 24.9 litres. Now let it undergo each process in turn.

Isothermal: temperature constant

PV = constant. The gas expands slowly while in contact with a heat reservoir. Since T does not change, ΔU = 0, so all the heat taken in becomes work.

W = nRT ln(V₂/V₁),   ΔU = 0,   Q = W
Doubling the volume: W = 1 × 8.314 × 300 × ln 2 = 1729 J. Q = 1729 J too.

Isobaric: pressure constant

The gas is heated under a free piston, so the pressure stays equal to the outside value.

W = PΔV = nRΔT,   ΔU = nC_vΔT,   Q = nC_pΔT
Doubling the volume means doubling the temperature to 600 K. W = P × V₁ = 10⁵ × 0.0249 = 2494 J. ΔU = 1 × 12.47 × 300 = 3741 J. Q = 3741 + 2494 = 6236 J. This process needs the most heat, since the gas must pay for both the work and the rise in internal energy.

Isochoric: volume constant

The container is rigid. V does not change, so W = P dV = 0. All the heat goes into internal energy.

W = 0,   Q = ΔU = nC_vΔT
Heating from 300 K to 600 K at constant volume: Q = ΔU = 3741 J. On the P-V graph this is a vertical line, with zero area under it.

Adiabatic: no heat exchange

The gas is insulated, or the process is so quick that no heat flows in or out. Q = 0, so W = −ΔU: the gas does work at the cost of its own internal energy and cools when it expands.

PV^γ = constant,   W = (P₁V₁ − P₂V₂)/(γ − 1),   Q = 0

For a monatomic gas γ = C_p/C_v = 5/3. If the gas expands to double its volume, T₂ = T₁(V₁/V₂)^(γ−1) = 300 × (1/2)^(2/3) ≈ 189 K. Then W = nC_v(T₁ − T₂) = 12.47 × 111 ≈ 1384 J, taken from the internal energy.

Same expansion, four stories

ProcessConstantW (J)ΔU (J)Q (J)
Isothermal (V doubles)T172901729
Isobaric (V doubles)P249437416236
Isochoric (T doubles)V037413741
Adiabatic (V doubles)Q = 01384−13840

Reading the P-V graph

Starting from the same point, the isobaric line is horizontal, the isochoric line is vertical, and the isothermal and adiabatic curves both fall as volume rises. The adiabatic curve is steeper than the isothermal, because the gas also cools as it expands, so the pressure falls faster. If you ever have to decide which curve is which, check the steepness: steeper is adiabatic.

Also remember the difference between a reversible and an irreversible process. The formulas above assume slow, quasi-static change. A sudden expansion into vacuum (free expansion) is adiabatic and does no work, so an ideal gas does not change temperature, even though no heat entered, which would fool anyone using "adiabatic means cooling" blindly.

Try it yourself

P-V Diagram Carnot Engine Kinetic Theory of Gases