Home / Electricity & Magnetism / Ohm's Law & V-I Curve

Ohm's Law & V-I Characteristics

NEETCBSE
V: 0 V I: 0 A R (V/I): 0 Ω

The physics

Ohm's law says current through a conductor is directly proportional to voltage, at constant temperature — giving a straight-line V-I graph through the origin. Not every device obeys this; a diode's current rises non-linearly (exponentially) with forward voltage.

Ohm's law: V = IR  (R constant — a straight line through the origin)
Non-Ohmic (diode): I doesn't scale linearly with V, so R = V/I changes at every point

Both curves are plotted from genuine physics — the resistor from V=IR directly, the diode from the same Shockley-equation model used in this site's dedicated p-n junction simulation.

Exam tip: a common NEET/CBSE question shows a curved V-I graph and asks for resistance "at point P" — you must compute V/I at that specific point, not the slope of the tangent (that would give the incremental/dynamic resistance, a different quantity).

Sample data: an ohmic resistor and a diode

A 10 Ω resistor obeys V = IR. The diode follows I = I₀(e^(V/nV_T) − 1) with the values below, so its resistance V/I changes at each point.

VoltageResistor currentResistor R = V/IDiode currentDiode R = V/I
0.2 V20 mA10 Ω4.58×10⁻¹¹ A4.37×10⁹ Ω
0.4 V40 mA10 Ω2.19×10⁻⁹ A1.83×10⁸ Ω
0.6 V60 mA10 Ω1.03×10⁻⁷ A5.85×10⁶ Ω
0.8 V80 mA10 Ω4.80×10⁻⁶ A1.67×10⁵ Ω
1.0 V100 mA10 Ω2.25×10⁻⁴ A4.45×10³ Ω

Conditions: I₀ = 10⁻¹² A, n = 2, V_T = 0.026 V (assumed silicon-diode parameters).

Notice: the resistor's V/I is 10 Ω at every voltage, which is why its V-I graph is a straight line through the origin. The diode's resistance falls by a factor of about a million over the same voltage range (from about 4×10⁹ Ω to about 4×10³ Ω), so it cannot be described by a single resistance value.

Quick answers

What is Ohm's law?
At constant temperature, the current through a conductor is proportional to the potential difference across it: V = IR. The V-I graph of an ohmic conductor is a straight line through the origin.
What is electric current and potential difference?
Current is the rate of flow of charge, I = Q/t, in amperes (1 A = 1 C/s). Potential difference is the work done per unit charge, V = W/q, in volts (1 V = 1 J/C).
What is resistivity?
ρ = RA/L, a property of the material and not of the shape. The unit is the ohm-metre (Ω·m) and the dimensional formula is [ML³T⁻³A⁻²].
Which devices do not obey Ohm's law?
Diodes, a filament lamp (resistance rises with temperature) and thermistors. Their V-I graphs are curved.

Read the full guide: Current electricity: Ohm's law, resistivity and Kirchhoff's laws

🎯 Practice Zone

Puzzle 1. 📈 An ordinary resistor's V-I graph is a perfectly straight line through the origin, while a diode's V-I graph is dramatically curved. What specifically makes a device "ohmic" versus "non-ohmic," and why does this distinction matter beyond just the graph's shape?

An ohmic device has a CONSTANT resistance (V/I ratio) regardless of the applied voltage or current — this is precisely why its V-I graph is a straight line with slope equal to R everywhere. A non-ohmic device's resistance genuinely CHANGES depending on the operating point (voltage or current), so V/I differs at every point along the curve, producing the characteristic curved shape. This matters practically because analyzing an ohmic circuit only requires one resistance value, while a non-ohmic device (like a diode or filament bulb) requires knowing the specific operating point before you can even determine its effective resistance at that instant.

Puzzle 2. 💡 A light bulb's filament is technically non-ohmic — its resistance measurably increases as it heats up under higher current. Why does this specific behavior mean a bulb's V-I graph curves in a particular direction (concave, bending toward the voltage axis) rather than the opposite?

As current increases, the filament heats up and its resistance rises — meaning each additional increment of current requires a disproportionately larger voltage increase to push through the now-higher resistance. This produces a V-I curve that bends increasingly steeply (concave toward the voltage axis) at higher currents, in contrast to a straight ohmic line. This behavior is directly opposite to many semiconductor devices (like diodes), which often show DECREASING effective resistance at higher operating currents — the direction of curvature genuinely reveals the underlying physical mechanism at work.

Puzzle 3. ⚡ At a single point on a curved (non-ohmic) V-I graph, there are two meaningfully different "resistance" values you could calculate: the static resistance (V/I, a straight line from origin to that point) and the dynamic resistance (dV/dI, the local tangent slope). Why do these give genuinely different numbers, and when does each one matter?

Static resistance (V/I) answers "what constant resistor would produce this exact same DC operating point?" — useful for basic DC circuit analysis at that specific operating condition. Dynamic resistance (dV/dI) answers "how does a SMALL additional change in current affect voltage right at this point?" — essential for analyzing small AC signals superimposed on a DC operating point, as in amplifier or diode circuit design. For an ohmic device these two values are identical everywhere (constant slope equals V/I everywhere), but for non-ohmic devices they generically differ, and conflating them is a very common source of exam errors.

Puzzle 4. 🌡️ A metal resistor's resistance increases with temperature, while a semiconductor's resistance typically DECREASES with temperature — genuinely opposite behaviors. How does this difference manifest if you plotted the same device's V-I curve at two different fixed temperatures?

For a metal resistor, the higher-temperature V-I curve would be less steep (lower slope, since higher resistance means more voltage is needed for the same current) than the cooler curve. For a semiconductor, the higher-temperature curve would instead be MORE steep (lower resistance, less voltage needed for the same current) — genuinely opposite trends. This is precisely why metals and semiconductors require completely different thermal design considerations in circuits — a metal resistor's self-heating tends to be self-limiting (increasing resistance reduces current), while a semiconductor's self-heating can be dangerously self-reinforcing (decreasing resistance increases current further, a phenomenon called thermal runaway).

Puzzle 5. 🔋 If you reverse the voltage polarity across an ordinary resistor, the V-I graph simply extends symmetrically into the third quadrant (negative V, negative I) — but a diode's reverse-bias behavior looks nothing like a mirror image of its forward behavior. What does this asymmetry tell you about the diode's underlying physics?

A resistor's symmetric V-I behavior reflects that its underlying physical mechanism (charge carriers being scattered by the material's atomic lattice) doesn't care about current direction — it resists current equally either way. A diode's dramatically asymmetric behavior — conducting easily in forward bias, blocking almost all current in reverse bias (until breakdown) — directly reflects its fundamentally directional internal structure (the p-n junction's depletion region behaves completely differently depending on which way charge carriers are being pushed). This asymmetry isn't a minor quirk; it's precisely the defining physical property that makes diodes useful for rectification and one-way current control.

Problem 1 (NEET level). 📘 A resistor's V-I graph is a straight line passing through (0,0) and (10V, 2A). Find its resistance.

R = slope = V/I = 10/2
R = 5 Ω

Problem 2 (JEE Main level). 📗 A non-ohmic device has V=1V, I=0.1A at one point on its curve. Find the static resistance at that specific point.

R_static = V/I = 1/0.1
R_static = 10 Ω (this value applies only at this specific point, not the entire curve)

Problem 3 (WBJEE level). 📙 At a different point on the same non-ohmic device's curve, V=2V and I=0.5A. Find the static resistance here, and confirm this device is indeed non-ohmic.

R_static = 2/0.5 = 4 Ω
Since this differs from the 10 Ω found in Problem 2 at a different point, the resistance is not constant — confirming this device is genuinely non-ohmic

Problem 4 (CBSE Class 12 level). 📕 For an ohmic resistor with R=5Ω, find the current at V=15V and V=25V, and verify the V-I graph's slope stays constant between these two points.

I(15V) = 15/5 = 3A; I(25V) = 25/5 = 5A
Slope = ΔV/ΔI = (25−15)/(5−3) = 10/2 = 5 Ω — exactly matches R, confirming constant slope (linearity) throughout, the defining feature of an ohmic device

Problem 5 (JEE Advanced style). 📓 A diode's current follows I=I₀(e^(V/0.026)−1) with I₀=1nA. Find the dynamic resistance (dV/dI) at V=0.6V, using the approximation dV/dI ≈ 0.026/I at that operating point (a standard diode small-signal result).

First find I at V=0.6V: I = (1×10⁻⁹)(e^(0.6/0.026)−1) ≈ 11.8 mA
Dynamic resistance ≈ 0.026/I = 0.026/0.0118
r_dynamic ≈ 2.2 Ω — notice this dynamic (small-signal) resistance is dramatically smaller than the static resistance V/I = 0.6/0.0118 ≈ 51 Ω at the same point, vividly illustrating why the two concepts from Puzzle 3 give genuinely different answers
🔬
1827

Georg Ohm publishes his systematic experimental study establishing that current through a conductor is proportional to applied voltage — initially dismissed by much of the German scientific establishment, but eventually recognized as one of the most foundational relationships in electrical science.

📊
Late 1800s

As electrical engineering matures into a rigorous discipline, systematically plotting V-I characteristic curves becomes a standard laboratory technique for characterizing new electrical components — distinguishing well-behaved ohmic conductors from more complex non-linear devices.

⚛️
1940s

The invention of the transistor and rapid development of semiconductor diodes at Bell Labs makes understanding non-ohmic V-I behavior genuinely essential — these devices' characteristic curves became fundamental design tools for the emerging field of solid-state electronics.

💻
Present day

V-I curve analysis remains a standard diagnostic and design tool across electrical engineering — from testing whether a component is functioning correctly, to designing amplifier circuits around a semiconductor's precise dynamic resistance at a chosen operating point.