Home / Electricity & Magnetism / Cells in Series & Parallel

Cells in Series & Parallel

Class 10CBSE
Combined EMF: 0 V Internal resistance: 0 Ω Terminal voltage: 0 V

The physics

Combining identical cells differently changes what you get: series adds up their EMFs (and their internal resistances), while parallel keeps the EMF the same as a single cell but reduces the combined internal resistance.

Series (n cells): EMF_total = nε  r_total = nr
Parallel (n identical cells): EMF_total = ε  r_total = r/n
Terminal voltage: V = EMF − I×r_total  (I = EMF_total/(r_total+R))

This is exactly why a torch needs cells in series (to get a high enough voltage to light the bulb), while a car's large battery uses cells arranged partly in parallel (to supply the huge current a starter motor needs without draining any single cell too fast).

Exam tip: a common Class 10 question asks which combination is better for a low-resistance external circuit — parallel wins here, since its lower internal resistance wastes less energy heating the cells themselves and delivers more current to the external circuit.

Sample data: current from 1 to 4 identical cells in series and in parallel

Each cell has EMF 1.5 V and internal resistance 0.5 Ω. Series: I = nε/(nr + R). Parallel: I = ε/(r/n + R).

Cells nSeries, R = 2 ΩParallel, R = 2 ΩSeries, R = 0.1 ΩParallel, R = 0.1 Ω
10.600 A0.600 A2.500 A2.500 A
21.000 A0.667 A2.727 A4.286 A
31.286 A0.692 A2.812 A5.625 A
41.500 A0.706 A2.857 A6.667 A

Conditions: ε = 1.5 V, r = 0.5 Ω per cell, external resistance R as shown.

Notice: the better arrangement depends on the load. With a large load (2 Ω) series gives 1.5 A against 0.706 A for four cells. With a very small load (0.1 Ω), where the internal resistance dominates, four cells in parallel give 6.67 A against 2.86 A in series.

Quick answers

What is EMF?
The energy supplied by the source per unit charge when no current flows, measured in volts. It is the open-circuit voltage of the cell.
What is terminal voltage?
V = ε − Ir. When current I is drawn, a part Ir is lost across the internal resistance r, so the terminal voltage is less than the EMF.
What are the rules for n identical cells?
In series: EMF = nε and internal resistance = nr. In parallel: EMF = ε and internal resistance = r/n.
When should you use series and when parallel?
Use series when you need a higher voltage. Use parallel when you need to supply the same voltage for longer, or a larger current through a small load resistance.

🔍 Explore More!

Think About It 1. 🔦 A torch (flashlight) needs two 1.5V batteries stacked one after another, end to end, to work properly — a single battery alone isn't quite bright enough. Why does simply adding a second battery in this particular way make such a difference?

Connecting batteries end-to-end (called "in series") adds their voltages together — two 1.5V batteries in series give you a combined 3V "push," roughly double what a single battery alone could provide. This extra push drives more current through the bulb's filament, making it glow noticeably brighter. This is exactly why so many battery-powered devices (torches, remote controls, toys) are specifically designed to use multiple batteries stacked in a row, rather than just relying on a single battery alone.

Think About It 2. 🔋 If you connect two identical 1.5V batteries side-by-side instead (in parallel, rather than end-to-end), does the combined voltage also add up to 3V, just like the series case?

No — connecting batteries in parallel keeps the voltage exactly the same as a single battery (still just 1.5V), rather than adding up. What parallel connection actually provides is extra CAPACITY — the two batteries can now supply more total current together, and importantly, each individual battery doesn't have to work as hard or drain as quickly, since they're sharing the load between them. This is genuinely useful when a device needs to run for a longer time on the same voltage, rather than needing extra "push."

Think About It 3. 🚗 A car's battery is actually made up of several individual cells connected together internally. Given that a car's starter motor needs an enormous burst of current to crank the engine, would you expect those internal cells to be connected mainly in series, mainly in parallel, or some clever combination of both?

Real car batteries actually use a clever combination of both! Cells are connected in series to build up the specific voltage needed (typically 12V total, made from six 2V cells in series), while groups of these series-connected cells are often also arranged in parallel to provide the huge burst of current a starter motor demands without excessively draining or damaging any single cell. This combined approach lets car battery designers get exactly the right voltage AND enough current capacity at the same time — neither series alone nor parallel alone would achieve both goals as effectively.

Think About It 4. ⚠️ If you accidentally insert one battery backward (reversed) in a series circuit of two batteries, does the device still work normally, work more weakly, or not work at all?

The device typically won't work properly at all, or will work much more weakly than expected! A reversed battery in series actually SUBTRACTS its voltage instead of adding it — two 1.5V batteries normally combine to give 3V, but if one is reversed, they effectively cancel each other's push almost entirely (1.5V − 1.5V = 0V, if the batteries are truly identical). This is exactly why battery compartments are carefully designed with specific + and − markings and matching shapes, to make sure batteries can only be inserted the correct way.

Think About It 5. 🔌 Why might a device that runs for a very long time on batteries (like an emergency flashlight meant to work for many hours) benefit from batteries connected partly in parallel, rather than just adding more batteries in series alone?

Parallel-connected batteries share the total workload between them — instead of one single battery having to supply all the current by itself and draining quickly, multiple batteries in parallel each contribute a smaller share, meaning each individual battery drains more slowly and the whole group lasts significantly longer before needing replacement. This is exactly why devices designed for long battery life (rather than needing extra voltage "push") often benefit from parallel battery arrangements, sharing the burden across multiple cells rather than relying on just one or two.

Try It 1 (Class 6-7 level). ✏️ Two 1.5V cells are connected in series. Find the total voltage.

Series voltage = 1.5 + 1.5
Total = 3V

Try It 2 (Class 7 level). ✏️ The same two 1.5V cells are instead connected in parallel. Find the total voltage.

Parallel connection keeps voltage the same as a single cell
Total = 1.5V (not doubled — only the current-supplying capacity increases)

Try It 3 (Class 8 level). ✏️ Four 1.5V cells are all connected in series. Find the total voltage.

Total = 1.5 × 4
Total = 6V

Try It 4 (Class 8 level). ✏️ Three 2V cells are connected in series, but one of them is accidentally inserted backward (reversed). Find the resulting total voltage.

Two cells add normally (2+2=4V), but the reversed cell subtracts instead of adding
Total = 2 + 2 − 2 = 2V — much less than the expected 6V!

Try It 5 (Class 9 level). ✏️ You need a 4.5V supply for a toy, and you only have 1.5V cells available. How would you connect them, and how many would you need?

Connect them in series (voltages add up)
Number needed = 4.5 ÷ 1.5 = 3 cells in a row
🔋
1800

Italian scientist Alessandro Volta built the world's first battery, called the "Voltaic Pile," by stacking many small individual cells (alternating discs of different metals with salty cardboard between them) one on top of another in a series arrangement — cleverly discovering that stacking cells this way multiplied the voltage far beyond what any single small cell could produce alone.

🔬
1836

English scientist John Frederic Daniell invented an improved, more stable battery design (the "Daniell cell"), which became widely used for early telegraph systems — reliable batteries connected cleverly in series and parallel combinations were absolutely essential for sending signals over long telegraph wires.

🚗
1859

French scientist Gaston Planté invented the first practical rechargeable lead-acid battery — the same basic design (six 2V cells connected in series) still used in virtually every conventional car today, over 160 years later, to reliably start the engine and power the electrical system.

🔌
Today

Understanding series and parallel cell connections remains essential for modern battery technology — from designing laptop and phone battery packs (which cleverly combine both arrangements), to engineering the huge battery packs inside electric cars, where careful combinations of series and parallel cells provide exactly the right balance of voltage and long-lasting range.